# ZERORUNOUT PBSwiss, GEDORE Silent Gear, Wiha CetroFix best in class custom ratcheting bit driver.

**Channel:** BZEUG
**Source:** https://www.youtube.com/watch?v=dvCh8M3n9AY
**Transcript page:** https://www.withtranscript.ai/video/dvCh8M3n9AY

## Chapters

- 0:00 — Introducing the Zero Runout Franken Driver
- 2:31 — Centro Fix Adapter Quality and Runout Caveats
- 5:18 — Measuring Combined Runout and Wobble
- 9:22 — Case Design Feedback and Improvement Suggestions
- 12:28 — Klein Chuck Comparison and Closing Thanks

## Transcript

**[0:00]:** Here it is, Zero Runout Studio. They sent me this. I put these bits in here. These bits do not come with this. Here it is, a PB Swiss handle, a silent ratchet ratchet, and a Centro Fix bit adapter, all from different manufacturers, all mashed together in a Franken driver. I don't really like the term Franken driver because Frankenstein's monster was kind of an ugly mix-matched kind of a thing. This is really taking the best in class, you know, bit chucks, ratcheting mechanisms. In in my opinion, PB Swiss makes one of the best handles in the industry. They just feel so good, but there are other good ones, too. Zero Runout Studios is putting these all together. So you've got to buy this from Zero Runout Studios, or you have to go out and buy the PB Swiss number three screwdriver. You got to take this out of the handle, so you've got a handle.

**[1:18]:** I'm pretty sure then they're drilling out the handle of the PB Swiss screwdriver because I don't think this diameter is just going to happen to be correct to receive the silent gear ratcheting mechanism, this mechanism here. So they got to pull this out of that, and then they've got to pull that whole thing out of the handle so that they've got this one mechanism as a module to then press into the PB Swiss handle, and then they got to press this Centro Fix adapter into Silent Gear module. And I'm not sure in which order they do it. I'm not sure how they do it, but that is what Zero Runout Studios is doing. And it's pretty remarkable because you end up with basically best in class handle ratcheting mechanism and bit chuck all in one unit that you can't buy from any one of these manufacturers.

**[2:31]:** Zero Runout Studios, okay? They know that the Centrofix adapter, if you don't know, is one of the best zero wobble, zero play bit holders out there. The other ones that I would mention are the Klein Tools Fast Bit True Grip. Um their chucks are also really amazing, but they're different. There is a little bit of compatibility differences and I've highlighted that in other videos. You know, I don't know. I wish Klein Tools would release this in an adapter. Um they don't have that yet in an adapter like this. Now the caveat with the Centrofix adapter, I'll give you affiliate links to buy these, to buy the Klein. Um and I'll put links to Zero Runout Studios all in the description of this video, of course. I do not have an affiliate relationship with Zero Runout Studios, by the way. But this adapter, the caveat with this is is that the runout or the wobble in this varies.

**[3:42]:** Like this one, this example is very good, but the first one that I ever bought years ago was horrible. You can see even a little bit more runout with this Centrofix Force. Um and it's got something to do with the way that they're pressing the hex shaft into that round hole, it distorts. And they get they get some that are really, really good, and they get some that are not good at all. So just be aware. I hope they got this fixed. I hope that they got the quality control issue fixed on these. So then the question in my mind was, okay, so what is the runout on this? Because it may not be obvious or well-known, but even on one of these high-price luxury screwdrivers from PB Swiss, there is runout between the shaft and the handle, and it's actually quite a bit. But because it's a low-speed hand tool, it really doesn't matter.

**[4:54]:** What matters is, is there any play? Is there any wobble? And it's a screwdriver, so of course it's zero. But there is runout. And then there's even runout in this Gedore. So there's runout between here and here. But it's it's very good. So little to no wobble, but yes, there is runout between these.

**[5:18]:** Okay, so then if you've got runout here, runout here, and you might have runout here, what happens when you put them all together? So I just I had to check this. I had to take a look. So I used this PB Swiss C6 long. They don't make these anymore, by the way. If they did, I would give you affiliate links to these bits. I really like them. They've got the C6 end rather than the E6. So I put this bit in my mini lathe, and I checked the runout on it, and there is a tiny amount of runout just in this bit. And then I put the zero runout driver on that to see what the runout was at the end of the handle. And there's a significant amount. But I do not want that to be any kind of a ding on Zero Runout Studios because they're really up against the runout that's in each one of these.

**[6:19]:** I mean, they are drilling this out. I think I think I can't imagine that those diameters just happen to be a coincidence. I don't know, maybe they are, but I I think they're having to drill this out. But it's really hard to take this object and put it in a vise, put it in some kind of a holder, and in some way hold it so that when you bore this out to receive the Godore Silent Ratchet that it's perfect. And I I really don't fault them at all. They're doing a good job. I mean, I can't figure out how they get this all pulled apart, drilled, and repress everything together, and it still looks factory new. Right? I mean, if if we're doing this by hand, you got to worry about scuffing this, scratching it, you know, messing up the coating on here. I think PB Swiss calls this Santoprene, right?

**[7:30]:** This this compound on here. You got to worry about messing that up. They're doing a really good job. I mean, I don't see any blemishes on this from the disassembly and reassembly process. I don't want to point out the runout in this as any kind of a insult or any kind of a ding on Zero Runout Studios. I really like what they're doing. And the fact of the matter is, I think we can all agree that the runout between here and here really doesn't matter. It's a hand tool. It's low RPMs. It It doesn't matter. It's just kind of an interesting curiosity um issue or question to kind of look into just to see what happens to the runout when you do that. Um you know it isn't the runout that matters. It's the wobble and there's no wobble. I mean there is it's in this.

**[8:33]:** It's in the silent ratchet. It's just the tiniest amount. Same as same as with this. Okay? Just the tiniest tiniest amount. It really is very very good for wobble. No wobble. It's just awesome. And of course the silent ratchet I mean you can't beat that for backdrag. It's it's basically a ball bearing, a sprag bearing. You just you can't beat it. So we're talking about runout on this handle. There's even runout on this Wihaha Centro Fix driver. But again it it doesn't matter because there's no bit wobble. The bit wobble is the thing that's annoying on these bit driver handles.

**[9:22]:** The other thing that I would offer as my opinion hopefully in a constructive way is that these bits do not fit in the lower area. You know you could go back into CAD and move these this way so you can have these bits. I think I think there might be enough room. And then you might be able to fit these in on that level. And and that's just a suggestion. It's a very very nitpicky thing of me. The magnets are good. It can break loose if it's dropped or something like that and some foam could be put in here, but the other thing that could be put in here is one more of these magnetic things. Um maybe offset somehow and then you could put longer stuff like this could go in there then. The long stuff can fit in here now. It just takes up two positions.

**[10:33]:** So my point isn't that it can't fit the long bits. My point is that over here on this side you've got some wasted space here. So I could either DIY put some foam in here so that when it closes it holds those bits in there so that when it's dropped then they stay they stay in there. But the other option would be if there was an additional 3D printed one of these racks with the magnets in them over here so that we could put even more bits in this case. He did a beautiful job on this case.

**[11:18]:** You really did. It's it's a nice case. It looks to be plenty durable. Um it's just that I I get to be a little bit of a stickler about wasted space on that stuff. My only other suggestion on this tool is one that I've made before is I think ideally this ring, the direction selector ring on the silent ratchet should be a larger diameter. And I don't know if there is a way to take this sleeve off, make a new sleeve and put it on there. That's probably asking way too much. But maybe something 3D printed that perfectly aligns up with these little ridges and kind of wedges on there so that if a guy wanted to he could even uh use some CA glue and glue on a larger diameter ring. It's it's it's top of the class. It's really really good. And it and the execution on the disassembly and reassembly is very very good.

**[12:28]:** Klein Tools has got a real winner here with this chuck. And that's another one to look into is this chuck and I'm not sure how it fits into the handle as a module. These size bits. So these fit pretty much perfectly in here. This size is really ideal for this. If you were looking for a set of bits to put in this if you were to buy this. You could outfit it with those. But you can see that it fits a lot of different things in here. Even as good as the Klein Tools is this chuck is so good. This handle style is super nice. Even this has run out. Yep. There's run out. There's no bit wobble. But there is run out. And of course it doesn't matter because it's low RPM. It's a hand tool. So I just again I got to say a big thank you to Zero Run Out Studios for sending this to me at no charge.

**[13:42]:** Good work. I love it. This one is going to be a non-affiliate link to Zero Run Out Studios. Check them out. I don't know if they're going to have Black Friday deals or not. I don't have any inside information on that. Go to their website. If they got a mailing list sign up for the mailing list. Follow them on social media. They do other things besides this. And I like their ideas and I like what what they do. It's really neat. And thank thank to my viewers who told me about Zero Runout Studio, because in the social media algorithms did not bring Zero Runout Studios content to me. It was through my viewers who told me about it. All right, if you like content like that, you know how YouTube works. Feed the algorithm for me. Stay tuned and thank you for watching.
